Archive for "GE Measurement and Control"

The New DPI620 Genii IS Multifunction Druck Calibrator- Safety in your Hands

GE Measurement and Control Nov 03, 2016 No Comments
The New Multifunction Druck Calibrator  
The new Druck DPI620 Genii IS multifunction druck calibrator combines best-in-class performance with ATEX and IECEx approvals for use in hazardous areas. Robust and weather-proof, the Genii IS puts you in control of all your pressure, electrical, temperature and frequency testing, with flexibility and accuracy giving you elite performance wherever you need it. Safety in your hands. Strong, light, intelligent And great under pressure. Packed with performance enhancing features, the Genii IS operates as a 3 in 1 calibrator, test meter and HART/Foundation Fieldbus communicator in hazardous zones where explosive gas and air mixtures can occur. Incorporating tool-free battery management with interchangeable battery packs, easy-to-use touch-swipe screen and daylight readable display as well as being the smallest and lightest calibrator of its type. When it comes to having all your calibration needs covered, stay safe, and stay ahead with the DPI620 Genii IS.  

Pitot Static Testers- Welcome to the wireless ADTS500 Series !

GE Measurement and Control Sep 13, 2016 No Comments

Pitot Static Testers

Testing an aircraft’s pitot static system is critical for the safe operation of that plane.static testers GE’s Static testers ADTS500 series of Air Data Test Sets are ideally suited for the task. Easy-to-use with innovative wireless handsets, swipe-screen commands and low cost of ownership. They cut down engineering time for standard maintenance, fault-finding and emergency aircraft-on-ground situations. With 4 models in the ADTS 500 series, GE has a solution that suits everyone from small light aircraft to the largest civil airliners. OIH is the agent is south africa for GE products and backs up the products with expertise service and knowledge .   Brochure  

Product Launch : Druck DPI 612 Flex Range Flexible Pressure Calibrator range

GE Measurement and Control May 20, 2016 No Comments

GE Pressure Calibrator DPI612

GEge logo pressure calibrator’s 5th generation dedicated pressure calibrator that combines pressure generation, signal measurement and loop power in one robust, easy-to-use instrument. Best in class accuracy, simple to use and fast acting, it takes the original ‘Druck’ to the next level in pressure calibration and measurement labeldpi612
  • The complete pressure calibration tool: pump, measure & analyse
  • Best in class accuracy
  • Interchangeable pressure modules for simple field re-ranging
  • Fast and dependable from vacuum to 1000 bar/15,000 PSI
  • Easy to use touch screen
  • No in-the-field leaks with the quick-to-fit pressure adaptors and hoses
  • Generates Pneumatic and Hydraulic Pump
For more information contact OIH pressure calibrator 3 versions dpi612

Flare Gas Mass Flow Meters

GE Measurement and Control May 10, 2016 No Comments
 gf868 banner flow meters
Brochure
DigitalFlow™ GF868 and XGF868i ultrasonic flow meters use patented Correlation Transit-Time™ technique and signal processing for the most accurate method of calculating molecular weight. Add to these the inherent advantages of ultrasonic flow measurement—reliability with no routine maintenance, high accuracy, fast response and wide rangeability—and GF868 and XGF868i flow meters are the clear choices for flare gas applications.
digitalflow gf868 flow meters

DigitalFlow™ GF868 Flare Gas Ultrasonic Flow Meter

digitalflowxgf868i flow meters

DigitalFlow™ XGF868i Flare Gas Ultrasonic Transmitter

OIH is the agent for GE products in South Africa and is backed by knowledgeable staff with years of expertise in the field. For more information please contact us

Calibration management software that empowers you

Calibration, GE Measurement and Control May 10, 2016 No Comments
 calibration management software

Calibration Management Software

Brochure

GE’s new Intecal v10 calibration management software provides an easy to use solution that integrates calibration scheduling, workflow, data collection, analysis and reporting into one automated system.
A fully automated paperless Calibration solution
  • Saves time by cutting out laborious paper work- 100% paper free calibration
  • Significantly improves productivity by integrating with leading calibrators
  • Makes calibration processes easier, simpler and more efficient
Always compliant and performant
  • Improves safety and reliability by reducing documentation time and errors
  • Supports GE’s Druck range of calibrators and others using FCINTF protocol
Imagine. Paper-free calibration. Data you need on hand. Error free & compliant.

GE Druck DPI611 Carry case available now!

GE Measurement and Control May 29, 2015 No Comments
Druck dpi611 carry case

Druck DPI611 Carry case

The Druck DPI611 carry case is made specifically to protect the Druck dpi611 calibrator.
  • Made from durable leather
  • DPI 611 can be used without removal
  • Pocket for test leads
  • Permits use of the hand strap
  • Shoulder strap provided
  • DPI 611 secured  - won’t fall out
  • Reinforced to protect the display
  • Battery and USB access
  • Anti-slip feet
OIH is the agent for Druck products in South Africa and is backed by a team hat has the technical knowledge and expertise to provide quality service on all of these products. For more information please contact us. We will be happy to assist you.

Calibration Management Software Update-GE Druck 4Sight

GE Measurement and Control May 12, 2015 No Comments
product notice calibration management software

4sight calibration management software

4Sight includes the latest driver to link the DPI 611, DPI 620 Series (including Genii and IS versions) and the PACE series to this scalable on premise or cloud based calibration management solution. The driver provides download/upload communications for the field calibrators and real time connection for workshop calibrators and multiple instrument calibration systems, for example, PACE controllers used in conjunction with the DPI 620 Genii.

Additions for Release 6.2.5.0

Data Import for Loops Loops and their associated Components can now also be imported using the Data Import screen in 4Sight. The Import Template has been updated to include an additional sheet

Issue In Bulk Notification When a list of Routines are selected from the Issue in Bulk page and the user clicks the Issue button, a popup will appear notifying the user that there will be selected number of Work Orders issued for the selected number of Routines. The user will be given the option to select Yes or No. When selecting Yes the system will proceed with issuing the selected Routines. When selecting No the system will not proceed and no Routines will be issued.

Routine Graph Information When the Work History Graph is viewed from the Routine Graph page, the Instrument Tag name and the Routine name are now displayed at the top of the graph.

Audit Trail New Data Updates Currently, when creating a new table record, the table fields whose value on creation does not differ from the default value for that field does not get recorded in the Audit Trail Details Table. The table fields whose value on creation differ from the default for that field do get recorded in the Audit Trail Details Table.

The Audit Trail Details table have been updated so that when a new record is created then the full list of fields relating to the new record will be recorded in the Audit Trail Details Table, regardless of whether their value has been modified from the default or not.

For example, when creating a Routine, the Input From value is defaulted to 0.0 on Routine creation. If the user assigns a value of 100 to the Input To option, without modifying the 0 value of the Input From option, when saving the routine with the Input Range 0 to 100, only the Input To value is logged in the Audit Trail Details. However, with these new Audit Trail updates the value of Input From as 0 will also be recorded, even if it is the same as the default value.

There have been no changes in the Audit Trail User Interface and there have been no changes to the Audit Trail main functionality. Also, there have been no changes to the Audit Trail Details table when editing a record.

Master Calibration List Excel Report The “Export to Excel” table button in the Instrument and Loop list pages have been updated to export the “Master Calibration List” to Excel. This report contains the following information for each Instrument or Loop:

Instrument Tag Description SOP Routine Name Last Date
Next Date Critical Interval IntervalType Ref Instrument
Status History Status Complete At Entry Out Of Cycle Deviation Allowable Overrun
Item Type Plant Area Class Company
Department Location Supplier Manufacturer Instrument Type
Type And Model Serial No Comments Purchase Date Purchase Cost
Purchase Order No Order Code Service Status In Service Date PID Code
Service Job No Computer Test Inst Identity Traceability
Certificate No Equipment No Ambient Temp Humidity Barometric Pressure
User Defined Field 1 User Defined Field 2 User Defined Field 3 User Defined Field 4 User Defined Field 5
User Defined Field 6 User Defined Field 7 User Defined Field 8 User Defined Field 9 User Defined Field 10
User Defined Field 11 User Defined Field 12 User Defined Field 13 User Defined Field 14 User Defined Field 15
User Defined Field 16 User Defined Field 17 User Defined Field 18 User Defined Field 19 User Defined Field 20
Input From Input To Output From Output To Cal Points
Output Points Lower Instrument Tolerance (-Adjust Level) Upper Instrument Tolerance (+Adjust Level) Input Unit Output Unit
Range Resolution Lower Process Tolerance Upper Process Tolerance Tolerance Type Points

KPI Filtering

The KPIs reports have been updated to provide the ability to filter the results by Class, Area and Plant. The KPI reports that have been updated are the following:

  • Item Service Status
  • Work Order Planned versus Unplanned
  • Work Order Status
  • Work Order Efficiency
  • Deviations
  • Task Results
  • Work Orders Due
  • References Used
  • Work Order Stock versus Time Cost
  • Work Order Actual Time Exceeds Estimated Time

Total Number of Records in Reports

The Reports in the Reports section of 4Sight have been updated to include the Total Number of records present in the generated reports.

The Reports that have been updated to display this additional information are the following:

  • Listings
  • References Used
  • Deviation Listings
  • Failed Tasks
  • Work Orders Done
  • Down Time
  • Due Date
  • Estimated vs Actual
  • History By Due Date
  • Labour and Stock Costings
  • Labour Costings
  • Work Order Labour Costings

Note: Any Reports not included in the above list either already display a total of the records in the report or is not applicable for displaying total number of records.

Additions for Previous Release 6.2.4.1

Company Name Editing

When an Instrument is in Edit Mode, a user is now able to edit the Company provided that the Company does not have any Routines in cycle.  Historical Work Order data is not changed when the Company or Department is changed for an Instrument.

References Filtering

When the “Filter by Company Department” configuration option is ON and the user has the “Use Filtering” option selected, then when issuing/entering a Work Order, the References list will display only those Reference Instruments available to the Company/Departments that the user is assigned to. Otherwise, all the reference instruments appear in the available list.

When the references are filtered then a “Show All” option is made available which allows a user to override the filtering and display all references for all companies and departments.

When the “Show All” option is checked or unchecked, the “Selected” list will remain the same and the “Available” list will be updated with the relevant References.

If a Selected Reference is de-selected it will be moved to the “Available” List regardless of the Show All option at the time of the de-selection. This will allow the user to re-select the Reference in the case where the reference was de-selected in error.

ERP Integration

The Work Order Configuration has been updated to include ERP System, ERP Authentication credentials and default Maintenance Cert Type for the ERP System. This allows for integrations with ERP systems.

Failed By User Deviation Message

When a Critical Routine is failed by a user using the “Failed By User” options, a deviation is created. Previously the deviation message would read “Calibration failed by user.” This message has been updated to instead read “Work Order failed by user” in order to make it more generic and allowing it to be applicable to non-calibration Work Orders.

Resolution “0”

4Sight has been updated to allow for a resolution of “0” for the Routine Type, Routine values tab and the Work Order Edit values tab. The accepted Resolution Range is not 0 to 5 instead of 1 to 5.

Crystal Reports Module

4Sight has been updated to allow for the inclusion of Crystal Reports based Certificates and Reports.

Cancelled/Rejected Status

When a Work Order is Cancelled or Rejected, a status message now appears on the applicable Work Order Certificate in Bold Red. For Cancelled Work Orders this message will read ‘Cancelled’ and for Rejected Work Orders this message will read ‘Rejected’.

The affected certificates are as follows:

  • Instrument Calibration Sheets
  • Loop Calibration Sheets
  • Instrument General Work Sheet
  • Loop General Work Sheets
  • Work Requests
  • PM Work Sheet

Product launch : AT600 Ultrasonic Flowmeter

GE Measurement and Control Jan 07, 2015 No Comments
product spotlight on ultrasonic flowmeter

Low Cost entry level ultrasonic flowmeter

The AT600 ultrasonic flowmeter combines state-of-the-art flow measurement capability in a clamp-on configuration at a lower cost.  

Why purchase the AT600?

With a new epoxy-coated aluminum industrial design, the AT600 delivers quality flow measurements in a clamp-on configuration and can be easily installed right at the process measurement point.   It is designed specifically for municipal applications such as water, wastewater, and other industrial flow applications

  Main features include:
  • Provides ultrasonic advantages at a lower cost
    Ultrasonic Flowmeter AT600

    Ultrasonic Flow Measurement AT600

  • Maintenance free operation, no calibration required
  • Simple setup and installation
  • Suitable for wide range of pipe sizes and materials

How Software Is Helping to Save the World | GE Software

GE Measurement and Control Nov 19, 2014 No Comments

GE Software

Posted by Deb Frodl, GE ecomagination Global Executive Director on Tue, 2014-11-04 17:17

GE software

  GE Predictivity™ Solutions Join ecomagination Portfolio It has been three years since Marc Andreessen, co-founder of the venture capital firm Andreessen Horowitz, wrote his influential essay, Why Software Is Eating the World. Since that time, the impact of software in industrial applications has grown substantially. GE’s Industrial Internet is playing an important role in advancing the use of software in this arena. However, in addition to eating the world, it has now become clear that software can play an important role in helping to save the world from growing resource scarcity. The fact is, a great global resource challenge is now upon us. The demand for natural resources is outstripping available supplies in many regions around the world. Regional resource imbalances are occurring for energy, water, food, and materials. These imbalances are driving up commodity prices and creating resource stresses that have social, political, and economic implications. This challenge is poised to become even greater in the years ahead. Expected increases in gross domestic product (GDP) and population levels over the next 15 years will translate into even stronger levels of resource demand. Our analysis indicates that in the absence of additional improvements in the intensity of resource use per dollar of GDP, both materials extraction and energy consumption will increase by 80% by 2030. Ecomagination is GE’s commitment to developing technologies that reduce our consumption of natural resources, while creating economic benefit for our customers. Established in 2005, GE’s ecomagination program has been at the forefront of resource productivity solutions for a decade. Now, with the addition of the Predictivity solutions to the ecomagination portfolio, GE has an even greater potential to play a key role in responding to the global resource challenge. The integration of efficient hardware with Internet-enabled software is the new frontier of natural resource productivity. This approach provides an avenue to achieve resource productivity improvements above and beyond those that can be achieved through hardware advances alone. In a recently published white paper on this topic, we call this Digital Resource Productivity, and we believe that productivity improvements can be doubled over the next 15 years by integrating software and hardware to optimize resource use. It would appear our customers agree. In a recent survey conducted jointly by GE and Accenture and captured in the Industrial Internet Insights Report for 2015, the ability to “improve environmental safety and emissions” was chosen as one of the top three priorities for the use of big data analytics in the next 1-3 years. Some examples of how the powerful combination of big machines and big data can have real world positive influences include: Power FlexEfficiency:  Uses data sensors and data science to produce up to 10% greater turbine power output Wind PowerUp:  Produces up to 5% additional power for wind farms Flight Efficiency Services:  Results in reductions of up to 1,600 lbs CO2 emission per flight and gains of up to 2% fuel efficiency using flight and operational data Trip Optimizer:  Produces up to 10% emissions reduction and up to 10% energy savings with a sophisticated optimization solution for rail Water & Process Technologies InSight™:  Enables industrial companies to reuse municipal wastewater instead of fresh water to meet the demand for cooling At GE, we are excited about the opportunity to play a role in helping to confront the global resource challenge. Today we are embarking upon a new frontier of digital resource productivity by expanding ecomagination to encompass GE’s Predictivity suite of solutions. Join us as we help transform the future of global resource productivity. via How Software Is Helping to Save the World | GE Software.

GE Smarter Calibration & Maintenance Webinar now Available on Demand

GE Measurement and Control Jul 23, 2014 No Comments
 
Now Available On-demand! GE Smarter Calibration & Maintenance Webinar  
webinarThe Smarter Calibration & Maintenance Webinar is now available on-demand for you to view anytime!   The webinar explores the gains achieved by implementing a smart calibration regime, such asimproved productivity, increased capacity, reduced downtime, cost savings and compliance. Whilst the presentation highlights the capabilities of our products (DPI620 Genii and 4Sight), the main objective of the presentation is to educate potential customers and address the day-to-day challenges of calibration, including:  
  • Background to the evolution of portable calibration and the development of paperless calibration.
  • Show the gains achieved from combined calibration and communication in today’s world of HART and Fieldbus and the incorporation of calibration into maintenance regimes.
  • Introduce the latest in portable calibration/communication technology (DPI 620 Genii)
  • Conclude with an insight into the world of web-based calibration management systems (4Sight) and how they interface with CMMS and high end ERP software.
  Click-here to view the webinar now!